Our propeller shafts are manufactured from bright ground 316 grade stainless steel and can be supplied in metric or imperial sizes up to 3" or 75mm diameter.
These shafts can be machined with either 1:10, 1:12, 1:16 or 1:20 tapers. They are supplied with nuts and keys ready for installation.



IMPERIAL SHAFTS
£


PRICES ARE EXCLUSIVE OF VAT



 

SHAFT
Dia

SINGLE TAPER
(3' Long Fully machined)
£

 

EXTRA Per 12"/152mm
£

EXTRA FOR DOUBLE TAPER

3/4"
£145
£15
£53
7/8"
£155
£20 
£53
1"
£150
£22
£53
1 1/8"
 £190
£44 
£58
1 1/4"
 £210
£37
£70
1 3/8"
POA
 
 
1 1/2"
£285
£53
£100
1 3/4"
£340
£71
£105
2"
£410
£93
£110
2 1/4"
POA
POA
POA
2 1/2"
POA
 
 
2 3/4"
POA
 
 
3"
POA
 
 
 
  
METRIC SHAFTS

Based on 1000mm overall length
 

SHAFT
Dia

SINGLE TAPER
(1m long fully machined)

EXTRA Per Foot/300mm
£ stg

EXTRA FOR DOUBLE TAPER
£ stg

22mm
£155
     
£20
     
£53
     
25mm
£150
                             
£22
                          
£53
                             
30mm
£210
                             
£34
                          
£58
                             
35mm
£260
                             
£45
                           
£70
                             
40mm
£275
                            
£60
                          
£100
                           
            45mm            

         

£360
                           
£75
                          
£105
                                                                                                                                               
Cost of keying parallel shaft and supply parallel key up to 2"/ 50mm - shaft diameter, from 2"/ 50 mm to 3"/ 70mm. Fitting a 1/2" coupling is extra. Please ring or e-mail for your specific requirements, such as lengths and tapers as all our Shafts are made to your exact requirements not mass produced.
Sizes and specifications may vary, surcharges may apply, please check when ordering.
DUPLEX STAINLESS is also available giving 30% increase in tensile strength over 316, it also has a greater resistance to corrosion all due to its higher chromium & molybdenum content. Enables smaller stern gear to be fitted, in some cases, with cost saving overall.
Available in 1", 1 1/4" 1 1/2", 1 3/4" & 2" diameter.

 
 

Propeller shaft dimensions  

 

STERN TUBE ASSEMBLIES


Lake stern tube assemblies are available to suit Shafts from 3/4"/20mm to 3"/70mm diameter, listed below are sizes to 1 3/4"/45mm. Larger sizes quoted against specific enquiry. Stern and gland bearing housings are cast in gunmetal to ensure good corrosion resistance; and come complete with cutlass bearings and gland packing. Length 'B' to suit your requirements. We also list options with P.S.S. seals , instead of the traditional style flexi stuffing gland inboard. Dimensions given below are for guidance only and may vary. Confirm when ordering any critical dimension on your installation. Customised sterngear quoted on receipt of detail.
This is our standard stern gear. We manufacture custom made systems to your requirements, please call to discuss your individual needs.

 

Dimensions Diagram
TYPE 1
Water Scoop Outboard bearing, Brass tube. Fixed flange inboard, nut type traditional gland ( stud type over 1 3/8" / 35mm )

 


 

for Shaft diameter 'd'
With traditional type stuffing gland 'B' Dimension at
12"-305mm
'B' Dimension Extra
per 12"-305mm
A
C
D
E

3/4"

20mm

RING OR EMAIL FOR PRICES

RING OR EMAIL

       FOR PRICES

4"

102

3.3"
84
1.5"
38
4"
102
7/8"
22mm
 
                                                                                         "
 
                                                              "
4.5"
114
3.3"
84
1.5"
38
4"
102
1"
25mm
 
                                                                                         "
 
                                                              "
5"
125
3.3"
84
1.5"
38
4"
102
1 1/8"
 
 
                                                                                         "
 
                                                          "
5.3"
135
3.3"
84
1.5"
45
4"
102
1.1/4".
30/35mm
 
                                                                                      "
 
                                                           "
6"/6.1/4"
150
3.5"
90
1.75"
45
4.5"
102
1.3/8"
30/35mm
 
                                                                                      "
 
                                                           "
6"/6.1/4"
150
3.5"
90
1.75"
45
4.5"
114
1 1/2"
40mm
 
                                                                                      "
 
                                                               "
7.4"
188
3.5"
90
2"
51
5"
127
1 3/4"
45mm
 
                                                                                         "
 
                                                                 "
7.4"
188
3.5"
90
2.1/2"
64
5"
127

  

 

Dimensions Diagram
TYPE 3

 

Type 3
Water Scoop Outboard bearing, Brass tube. Inboard mounting flange. Flexible inboard bearing, nut type traditional gland or PSS seal. ( stud type over 1 3/8" / 35mm)

 

for Shaft diameter 'd'
With traditional type stuffing gland 'B' Dimension at
12"-305mm
With P.S.S seal
'B' Dimension at
12"-305mm
 
' B' Dimension
Extra
per
12"-305mm

 
A
C2
D
E

3/4"

20mm

RING OR EMAIL FOR PRICES

RING/ EMAIL

 
RING/ EMAIL

4"

102

6.5"
165
1.5"
38
4"
102
7/8"
22mm
 
                                                                                   "
 
                                         "
 
                                          "
4.5"
114
6.5"
165
1.5"
38
4"
102
1"
25mm
 
                                                                                      "
 
                                      "
 
                                          "
5"
125
6.5"
165
1.5"
38
4"
102
1 1/8"
 
 
                                                                                      "
 
                                          "
 
                                          "
5.3"
135
3.3"
165
1.5"
45
4"
102
1.1/4".
30/35mm
 
                                                                                "
 
                                       "
 
                                      "
6"/6.1/4"
150
7.5"
190
1.75"
45
4.5"
102
1.3/8"
30/35mm
 
                                                                             "
 
                                          "
 
                                          "
6"/6.1/4"
150
7.5"
190
1.75"
45
4.5"
114
1 1/2"
40mm
 
                                                                               "
 
                                         "
 
                                          "
7.4"
188
7.5"
190
2"
51
5"
127
1 3/4"
45mm
 
                                                                             "
 
                                          "           
 
                                                 "
7.4"
188
7.5"
190
2.1/2"
64
5"
127

  

 Shaft Dimensions
TYPE 4

 

TYPE 4
Plain GRP tube and Flexible nut type traditional gland or PSS seal ( stud type over 1 3/8" / 35mm) 'P' strut and cutless bearing ( see seperate listing for further detail) can be used with 'A' Bracket etc.

 

 
for Shaft diameter 'd'
With traditional type stuffing gland 'B' Dimension at
12"-305mm
With P.S.S seal
'B' Dimension at
12"-305mm
 
' B' Dimension
Extra
per
12"-305mm

 
C1
D
F

3/4"

20mm

 

  RING OR EMAIL FOR PRICES
  RING OR EMAIL       FOR PRICES
RING OR EMAIL  
   FOR PRICES

4"

102

1.63"
41
10"
254
7/8"
22mm
 
                                                                           "
   
                                                     "
 
                                                   "
4"
102
1.63"
41
10"
254
1"
25mm
 
                                                                                 "
 
                                            "
 
                                                "
4"
102
1.75"
51
15.75"
400
1 1/8"
 
 
                                                                              "
 
                                            "
 
                                                   "
4"
102
2"
51
15.75"
400
1.1/4".
30/35mm
 
                                                                                 "
 
                                            "
 
                                                "
4.8"
122
2.25 "
57
15.75"
400
1.3/8"
30/35mm
 
                                                                              "
 
                                               "
 
                                                   "
4.8"
122
2.5"
64
17.72"
450
1 1/2"
40mm
 
                                                                              "
             "
 
                                                    "
5.3"
135
2.5"
64
17.72"
450
1 3/4"
45mm
             
                                                                              "
 
                                               "
 
                                                    "
5.3"
135
3"
76
21.65"
450
  

 

Dimensions of propeller shaft
TYPE 5

 

TYPE 5
GRP tube with cutless bearing outboard, Flexible inboard bearing and nut type traditional gland pr PSS seal (stud type over 1 3/8" / 35mm)

 

for Shaft diameter 'd'
With traditional type stuffing gland 'B' Dimension at
12"-305mm
With P.S.S seal
'B' Dimension at
12"-305mm
 
C1
D

3/4"

20mm

4"

102

1.63"
41
7/8"
22mm
 
                                                                                                 "
 
                                                                   "
4"
102
1.63"
41
1"
25mm
 
                                                                                              "
 
                                                                       "
4"
102
1.75"
51
1 1/8"
 
                                                
                                                                                           "
 
                                                                       "
4"
102
2"
51
1.1/4".
30/35mm
 
                                                                                                 "
 
                                                                 "
4.8"
122
2.25 "
57
1.3/8"
30/35mm
 
                                                                                              "
         
                                                                   "
4.8"
122
2.5"
64
1 1/2"
40mm
 
                                                                                           "
 
                                                                   "
5.3"
135
2.5"
64
1 3/4"
45mm
 
                                                                                                 "
  
                                                                   "
5.3"
135
3"
76
  
 
www.lakesterngear.co.uk © 2015

Hosted by SiteWeavers